حلول واجبات الجامعة العربية المفتوحة ~~

حلول واجبات الجامعة العربية المفتوحة لجميع تخصصات الجامعة ولجميع فروع الجامعة حلول واجبات – مشاريع تخرج – ملخصات هامة Mobile: 00966542495275 حلول واجبات الجامعة ا
 
الرئيسيةاليوميةس .و .جبحـثالتسجيلدخول

شاطر | 
 

  حل واجب t216b spring 2016

اذهب الى الأسفل 
كاتب الموضوعرسالة
whatsapp::00966542495275
Admin


عدد المساهمات : 1234
تاريخ التسجيل : 19/08/2010
العمر : 30

مُساهمةموضوع: حل واجب t216b spring 2016   الإثنين سبتمبر 26, 2016 9:15 am


Question 1 (13 marks)
The marks of this question are based on the scores you obtain in the Cisco Scaling networkschapters’ exam; these exams are found in the Cisco Academy website.

There are 9 chapter exams for this question; all the exams have the same weight and are over 100. The tutor will download the grade of the exams from the Cisco website after the cut-off date.


Note 1: The average score is over 13
Note 2: Use This table is for your own information; you can use the following formula to calculate your own average score for this question:[∑tests/900]*13
∑tests = test1+ test2+…+test9

Test 1 Test 2 Test 3 Test 4 Test 5 Test 6 Test 7 Test 8 Test 9 Average score
over 13


Question 2 (14 marks)
The mark for this question is based on the score you obtain in the Cisco Scaling networksfinal exam.

The tutor will download the grade of the exams from the Cisco website after the cut-off date

Note: The average score is over 14
Note2: Use the following formula to calculate your average score: [test/100]*14


Question 3 (67 marks)

This question allows you to demonstrate your ability to program a network of Cisco switches using packet tracer. The Packet tracer file for this question is T216BFA15TMA01Q3.pkt will be found on the AOULMS (Moodle).

Configuration
Configure your network as shown in figure 1 using (Command Line Interface) instructions. Your configuration should be complete as possible.

Topology Diagram

Learning Objectives
To complete this question:
• Configure Device Basic Settings
• Configure LAN Redundancy and Link Aggregation
• Configure EIGRP Dynamic Routing Protocol
• Verify Network Connectivity and HSRP Configuration
• Document the configuration

Scenario
This question tests your skills and knowledge that you learned in CCNA level 3. You are asked to configure the switches to support IPv4 connectivity and LAN redundancy. You will then an LCAP EtherChannel, verify connectivity and document the configuration.

Addressing Table

Device Interface IP Address Subnet Mask Default Gateway
R1_xxxxxx G0/1 192.168.5.1 255.255.255.0 N/A
S0/0/0 142.42.0.1 255.255.255.252 N/A
Lo1 172.27.1.1 255.255.255.0 N/A
Lo2 172.27.2.1 255.255.255.0 N/A
Lo3 172.27.3.1 255.255.255.0 N/A
R2_xxxxxx S0/0/0 142.42.0.2 255.255.255.252 N/A
S0/0/1 142.42.0.5 255.255.255.252 N/A
Lo0 209.165.200.225 255.255.255.248 N/A
R3_xxxxxx G0/1 192.168.5.3 255.255.255.0 N/A
S0/0/1 172.27.123.6 255.255.255.252 N/A
Lo4 172.27.4.1 255.255.255.0 N/A
Lo5 172.27.5.1 255.255.255.0 N/A
Lo6 172.27.6.1 255.255.255.0 N/A
S1_xxxxxx VLAN 1 192.168.5.11 255.255.255.0 192.168.5.2
S2_xxxxxx VLAN 1 192.168.5.12 255.255.255.0 192.168.5.2
S3_xxxxxx VLAN 1 192.168.5.13 255.255.255.0 192.168.5.2
PC-A NIC 192.168.5.21 255.255.255.0 192.168.5.2
PC-B NIC 192.168.5.22 255.255.255.0 192.168.5.2
PC-C NIC 192.168.5.23 255.255.255.0 192.168.5.2
Table A

Note: XXXXXX is your ID (6 digits)
Note2: the interfaces of the PCs and the servers are already configured.
Part 1. Configure Device basic setting. (12 marks)
Configure routers and switches according to the following guidelines:
• Configure the hostname* (the hostname of the switch should be as follow R1_XXXXXX for
router R1 where XXXXXX is your AOU short ID)
• Disable DNS lookup.
• Configure an encrypted privileged EXEC password. "A216B_XXXXXX”
• Configure a valid* message-of-the-day banner for example: “Only authorized personnel are allowed to access the device” or “This is a secure system. Authorized Access only” or “Legal action will be pursued for any unauthorized use”.
• Configure a password for console connections. “salking@”
• Configure synchronous logging.
• Configure a password for auxiliary connections. “he7lo”
• Configure a password for vty connections. “partible#”

* the router or switches should include your ID, for example: for Switch1: S1_120567; for Router1 R1_120567

List in the beneath tables the commands you used for each devices (routers and switches).

The commands should include the command prompt as seen on the router for example:
• S1_123456(config-if)#ip address 192.168.0.2 255.255.255.0 (this is correct)
• ip address 192.168.0.2 255.255.255.0 (this is incorrect)

Step 1: Configure Router R1.(2 marks)
Router R1
Tasks Command(s)
Configure the hostname* (as mentioned in table A)
Disable DNS lookup.
Secure the privileged EXEC access using the following password “A216B_XXXXXX”
Configure a valid* message-of-the-day banner
Configure a password for console connections. “salking@”
Configure synchronous logging
Configure a password for auxiliary connections. “he7lo”
Configure a password for vty connections. “partible#”
Note: Save the running configuration to the startup configurationusing the following command:
“copy running-configstartup-config”


Step 2: Configure Router R2.(2 marks)
Router R2
Tasks Command(s)
Configure the hostname* (as mentioned in table A)
Disable DNS lookup.
Secure the privileged EXEC access using the following password “A216B_XXXXXX”
Configure a valid* message-of-the-day banner
Configure a password for console connections. “salking@”
Configure synchronous logging
Configure a password for auxiliary connections. “he7lo”
Configure a password for vty connections. “partible#”
Note: Save the running configuration to the startup configurationusing the following command:
“copy running-configstartup-config”



Step 3: Configure Router R3.(2 marks)

Router R3
Tasks Command(s)
Configure the hostname* (as mentioned in table A)
Disable DNS lookup.
Secure the privileged EXEC access using the following password “A216B_XXXXXX”
Configure a valid* message-of-the-day banner
Configure a password for console connections. “salking@”
Configure synchronous logging
Configure a password for auxiliary connections. “he7lo”
Configure a password for vty connections. “partible#”
Note: Save the running configuration to the startup configurationusing the following command:
“copy running-configstartup-config”




Step 4: Configure Switch S1.(2 marks)
Switch S1
Tasks Command(s)
Configure the hostname* (as mentioned in table A)
Disable DNS lookup.
Configure a secure the privileged EXEC access using the following password “A216B_xxxxxx”
Configure a valid* message-of-the-day banner
Configure a password for console connections. “salking@”
Configure synchronous logging
Configure a password for vty connections. “partible#”
Encrypt password display
Note: Save the running configuration to the startup configurationusing the following command:
“copy running-configstartup-config”




Step 5: Configure Switch S2.(2 marks)
Switch S2
Tasks Command(s)
Configure the hostname* (as mentioned in table A)
Disable DNS lookup.
Configure a secure the privileged EXEC access using the following password “A216B_xxxxxx”
Configure a valid* message-of-the-day banner
Configure a password for console connections. “salking@”
Configure synchronous logging
Configure a password for vty connections. “partible#”
Encrypt password display
Note: Save the running configuration to the startup configurationusing the following command:
“copy running-configstartup-config”


Step 6: Configure Switch S3.(2 marks)
Switch S3
Tasks Command(s)
Configure the hostname* (as mentioned in table A)
Disable DNS lookup.
Configure a secure the privileged EXEC access using the following password “A216B_xxxxxx”
Configure a valid* message-of-the-day banner
Configure a password for console connections. “salking@”
Configure synchronous logging
Configure a password for vty connections. “partible#”
Encrypt password display
Note: Save the running configuration to the startup configurationusing the following command:
“copy running-configstartup-config”


Part 2. Devices Interface configuration (15marks)
List in the beneath tables the commands you used for each router

Step 1. Configure R1 interfaces (3.25 marks)
Router R1
Configuration Item or Task Specification Command(s)
Interface G0/1 • Set the description
• Set the Layer 3 IPv4 address. Refer to Table A for IPv4 address information.
• Activate interface
Interface S0/0/0 • Set the description
• Set the Layer 3 IPv4 address. Refer to Table A for IPv4 address information.
• Set a clocking rate of 800000.
• Activate interface
Interface Lo1 Set the Layer 3 IPv4 address. Refer to the Addressing Table for IPv4 address information.
Interface Lo2 Set the Layer 3 IPv4 address. Refer to the Addressing Table for IPv4 address information.
Interface Lo3 Set the Layer 3 IPv4 address. Refer to the Addressing Table for IPv4 address information.


Step 2. Configure R2 interfaces (2.75 marks)
Router R2
Configuration Item or Task Specification Command(s)
Interface S0/0/0 • Set the description
• Set the Layer 3 IPv4 address. Refer to Table A for IPv4 address information.
• Activate interface
Interface S0/0/1 • Set the description
• Set the Layer 3 IPv4 address. Refer to Table A for IPv4 address information.
• Set a clocking rate of 800000.
• Activate interface
Interface Lo0 (Simulated Internet connection) Set the description.
Set the Layer 3 IPv4 address to 209.165.200.225/29.
Default route Configure a default route out Lo0.


_________________
الإجــابة النمــوذجية
----------------------

[عزيزي الزائر يتوجب عليك التسجيل لمشاهدة الإجابة النموذجية ، للتسجيل اضغط هنا] || الكاتب: [عزيزي الزائر يتوجب عليك التسجيل لمشاهدة الإجابة النموذجية ، للتسجيل اضغط هنا] || المصدر: [عزيزي الزائر يتوجب عليك التسجيل لمشاهدة الإجابة النموذجية ، للتسجيل اضغط هنا]






خدمات مجانية – حلول واجبات الجامعة العربية المفتوحة
لجميع تخصصات الجامعة ولجميع فروع الجامعة
حلول واجبات – مشاريع تخرج – ملخصات هامة
http://aou888.123.st/
Mobile: 00966542495275  or 0542495275
Watsapp: 00966542495275

smsm.hamdy66@yahoo.com
حلول مضمونة وغير مكررة وغير متشابهة لجميع واجبات الجامعة
متوفرمدرسين ومدرسات لجميع المواد والتخصصات
KSA-Kuwait-Bahrain-Oman-Jordon-Lebanon-Egypt
الرجوع الى أعلى الصفحة اذهب الى الأسفل
http://aou888.123.st
 
حل واجب t216b spring 2016
الرجوع الى أعلى الصفحة 
صفحة 1 من اصل 1
 مواضيع مماثلة
-
» خطط التحسن ونظم المتابعة لجميع المجالات2016/2017
» تسريب اقوى مراجعة ديناميكا بخط اليد بها كل اسئلة امتحان ديناميكا 3 ثانوى نظام حديث 2014

صلاحيات هذا المنتدى:لاتستطيع الرد على المواضيع في هذا المنتدى
حلول واجبات الجامعة العربية المفتوحة ~~  :: حلول واجبات 2017/2018 AOU(يشاهدة الآن 1253 زائر) :: جروب الامتياز2017/2018-
انتقل الى: